Pro-face PS-3700A Instalační příručka stáhnout pdf (Strana 1)

E-1

Preface

The PSA-HD20 is made by Pro-face for use with PS-3700A Series (hereafter referred

as the "PS-A") units. This 2.5 inch 20GB hard disk is designed to be installed inside

the PS-A unit.

Corresponding units: PS-3700A Series units

(All product names that appear in this guide are the trademarks of their re-

spective companies)

Pro-face: Digital Electronics Corporation (in Japan and other countries)

MS-DOS

, Windows

: Microsoft Corporation (USA)

To Prevent Accidents

• Since the PSA-HD20 is a precision instrument, be sure it is neither hit by nor pressed

strongly against another object. After unpacking, be sure the unit is not dropped or

jolted during installation. Also, a PS-A unit built in to a larger piece of equipment (i.e.

operation panel) should be removed and packed separately prior to shipping.

• Be sure water, liquids or metal particles are not allowed to enter the PSA-HD20. Any of

these may cause either a breakdown or an electrical shock.

• Do not place or store this unit in a location where there is direct sunlight, excessive heat,

dust or vibration.

• Do not store or operate the PSA-HD20 near chemicals, or where there are chemical

fumes.

• Do not allow anyone other than Pro-face’s own service staff to perform maintenance or

adjustments to the PSA-HD20.

• Do not move or shift the PS-A unit while the PSA-HD20 is installed and the PS-A unit's

power is ON.

• Do not use the PSA-HD20 in locations where corrosive gasses are present, since they

can lead to a hard disk breakdown.

• To prevent damage to file data, be sure to shut down the PS-A unit's OS before turning

OFF the main power.

• To prevent HDD memory leaks, restart the OS periodically.

• In order to extend the lifetime of the hard disk, Pro-face recommends you set the Win-

dows [Control panel]-[Power Management option]-[Turn off hard disks] selection to

turn the hard disk off when the unit is not being operated. A setting of 5 minutes is

recommended.

• Be sure to check that the PS-A unit’s power is disconnected

before installing the unit, in order to prevent an electrical shock.

• Do not attempt to modify or open the PSA-HD20, since it can

cause a shock or fire.

• When installing the PSA-HD20, be sure to read this guide's “2.

Installation” section’s information completely to ensure that the

unit is correctly installed.

WARNINGSWARNINGS

1 2 3 4 5 6 7 8

Shrnutí obsahu

Strany 1 - WARNINGSWARNINGS

E-1PrefaceThe PSA-HD20 is made by Pro-face for use with PS-3700A Series (hereafter referredas the "PS-A") units. This 2.5 inch 20GB hard dis

Strany 2 - Hardware Specifications

E-2• The PSA-HD20 has a finite usage lifetime. Therefore, be sure to backup all HDD data periodically or prepare a backup HDD unit.• The HDD unit&ap

Strany 3 -  Environment

E-3• The environment specifications given here are for a PSA-HD20installed in a PS-A unit.• Pro-face does not guarantee the preservation of any data

Strany 4 - WARNINGS

E-4Since the HDD unit is a precision instrument that has a low resistance toshocks, be sure it is neither hit by nor pressed strongly against anothero

Strany 5 - ESP6000 - 667MHz Model)

E-51)Place the PS-A unit face down andunscrew eight (8) attachmentscrews. (See diagram)2)Lift the Rear Cover off of the PS-A unit.3)Insert the PSA-HD2

Strany 6 - 4 Hardware Setup

E-64 Hardware SetupAll the following explanation screens use the PS-A unit's factory settings (defaultsettings).• Normally, the factory default

Strany 7 - Software Setup

E-7Software Setup4After completing the hardware setup, in order to save data and application(s) to theHDD, use your OS (MS-DOS® or Windows®) to create

Strany 8